All About Daily Raleigh News

Air Duct Installation Columbus OH

Jun 19

7 STEPS TO EASY HVAC Duct Installation

Do you want to install ductwork in your business or home?

Modern life requires a functioning HVAC system. It can be daunting to set up an HVAC system, whether you're looking to make improvements or replace old ducting. It doesn't have to be.

Continue reading to learn how to install HVAC ducts easily.

1. CONSTRUCT THE VENTILATION EARLY

Before installing any type of ductwork, it is necessary to calculate your load calculation. This means that you must calculate the heat gain and loss in each room. This will tell you which rooms require ductwork and which can be done without.

Draw a diagram and write down your calculations. After you have completed your calculations, you are ready to plan your project. Spend some time determining where the ductwork should be. It is also important to plan the locations of the air return ducts.

Although it doesn't need to be a complete blueprint, you should try to be as detailed and precise as possible. It is important to give accurate measurements for each room. This will allow you to measure the rooms and determine how much material and equipment are needed.

2. SEEK THE RIGHT DUCTING

You have two options when it comes to ductwork: sheet metal or flexible fiberglass. Sheet metal ductwork is proven to be reliable, effective, and tested.

Sheet metal ductwork can be used to build new properties or repair existing ones. You may not need to repair your sheet metal ductwork if it is installed correctly and maintained properly.

Sheet metal also has some other advantages. Sheet metal is easy to install and makes it ideal for DIY installations. It can be used in most homes because it comes in many sizes and fits. Sheet metal is more durable and doesn't collect as much dust.

Flexible fiberglass ducting can degrade over time. It can collect dust and be difficult to clean. To get the same airflow, they will need to be bigger than metal ducting. It can restrict airflow by creating kinks or not leaving enough space around corners.

3. PICK THE LOCATION OF YOUR HVAC FIRST

Choose the best location for your exhaust pipes or large parts. Imagine how simple it will be for everything to be connected. Lofts are often used for heat recovery and MVHR systems. You can store them in a utility room if there aren't enough space or vaulted ceilings.

Ceiling voids between floors or lofts are where ducting is most commonly found. Vaulted ceilings don't permit this because there aren't any ceiling voids. Instead, they can be run between floors or within stud walls using webbed eco joists.

4. Avoid long runs and bends

Airflow will be affected by any bend, regardless of whether or not it is properly sealed. You can risk placing equipment too far from the cooling area if you don't spend enough time in the design phase. This can cause long ductwork runs that make it difficult for the HVAC unit to cool the room.

Airflow will be reduced if there are too many bends or bends that are too steep. This reduces the airflow to the cooling area, which causes your HVAC system to work harder and causes the room to heat up.

5. Work with an existing cropping system

It is often easier to integrate existing ductwork into your new system if you have it. It is important to not repurpose any ductwork that requires to be replaced.

It is not always possible to use best practices when installing ductwork. Installing a pipe between two other pipes is not always possible. A draw band connector is useful for securing circular ductwork.

Don't attempt to peel the foil tape from between sections of your ductwork when you're tearing it apart. Instead, score the seams and remove all screws from the tape. This will give you a smooth surface on which to apply new tape. You can then remove any debris and tape the tape on the top.

6. SEAL PROPERLY

Your conditioned air could be lost up to 20% if your ductwork has not been sealed properly. High-efficiency systems have a higher capacity and last longer.

This is because air has more time in the ducts, and therefore more chance to escape from joints. You can prevent leaks by sealing your joints with mastic or metal-backed tape.

7. COMMISSION AIRFLOW TO CONTROL

After your ductwork has been installed, make sure you do a final inspection. Check that your HVAC unit is operating at the right airflow level.

Many of the most recent models can be controlled via an app. This saves installers time and reduces their workload. The app allows them to verify that the airflow levels are correct. The app eliminates the need to return to the control panel to manually adjust fan speeds.

This ensures that everything is properly commissioned. It is important to ensure that everything runs at its maximum capacity upon installation. You might have to pay a costly callback in order to correct any problems.

HVAC DUCT INSTALLATION IS EASY

These 7 steps will ensure that your HVAC duct installation goes smoothly.

You can avoid many potential problems by planning your Air Duct installation Columbus OH in advance. You can ensure a durable installation with minimal maintenance by choosing the right materials.

 

Columbus Airduct Cleaning

Columbus, OH

(740) 291 0950